Slide 3
Slide 1
Slide 2
 

M2M TeleSystems Equipment



M2M TeleSystems Equipment: WebGate 3G interface module
WebGate 3G interface module
Your Gateway to the internet and FarmQuest! The WebGate 3G interface module connects your electronic controllers and equipment on the farm to the FarmQuest server via the internet. On the farm, the WebGate 3G can connect wirelessly to onsite control equipment, using the WiFarm network (wire option is also available). Similarly, the onsite WebGate 3G is connected to the internet using an ethernet cable or various wireless connections (cellular, satellite, etc.). All descriptions and characteristics can be changed without notice or...

 More



M2M TeleSystems Equipment: WiFarm wireless communication network
WiFarm wireless communication network
The WiFarm is a wireless communication network for use with your controllers based on our popular Core technology. WiFarm is a highly versatile wireless technology, which can be accessed by any controller equipped with our Core technology.  Simply install an RF-IN or RF-IN2 wireless module in the Core of your controllers, and by using the unique ID number found on each RF-IN card, you will be able to easily create your 128 bit encrypted wireless network. The WiFarm technology uses a mesh network, which allows controllers to communicate with each other and pass on information from one...

 More



M2M TeleSystems Equipment: FarmSite management software
FarmSite management software
FarmSite allows you to view, navigate and adjust your controllers, analyze graphs, and accumulate data using a direct wired onsite computer or a modem. FarmSite is a management software specifically developed for livestock operations. Using the PCGate 3G hardware, your onsite controllers can communicate with local computers wirelessly connected to the WiFarm network (direct wire option is also available). There is no need for an internet connection with FarmSite! All descriptions and characteristics can be changed without notice or...

 More



M2M TeleSystems Equipment: RF-IN and RF-IN2 wireless modules
RF-IN and RF-IN2 wireless modules
Get the most out of your controllers with the RF-IN and RF-IN2 wireless modules! Easy to install, the RF-IN/RF-IN2 wireless modules eliminate the need for trenching and the additional costs for material and labor typically required for wiring installations.  With these transmitting and receiving wireless modules, you can remotely monitor and manage your controllers.  A wireless connection presents the added advantage of reducing the risk of lightning damage to your electronic controllers. When teamed up with the WebGate 3G, the WiFarm network using RF-IN...

 More



M2M TeleSystems Equipment: RF-P4
RF-P4
The RF-P4 module has 4 multi-purpose ports which are managed and controlled directly by FarmQuest online management service via the WebGate3G internet gateway. This innovative module can be used for  remote data acquisition, surveillance, and even control relays. Here are some of the many applications it can be used for:      - Temperature sensors      - Humidity sensors      - Static Pressure sensors      - Sensors equipped with a 4 to 20 mA output signal       - Sensors equipped...

 More



M2M TeleSystems Equipment: Access Lock
Access Lock
The Access Lock module is designed to control the access of personnel into livestock buildings for biosecurity. This module restricts the entry and exit to autorized personnel only. To gain entry, simply place a valid access card near the card reader to unlock the door. Easy to install, with 2 simple steps required for programming user access rights, this module can be programmed with up to 100 users per card reader. The Access Lock module can be installed as a stand alone unit, where it will be effective at restricting access to valid users, and can also be connected wirelessly to the FarmQuest online...

 More



M2M TeleSystems Equipment: RF-ACCESS
RF-ACCESS
There is no obstacle too high for the WiFarm network with RF-ACCESS! The RF-ACCESS is used whenever obstacles such as building walls reduce the strength of the wireless signal.  Once the RF-ACCESS installed, the wireless signal can easily pass through obstacles without losing signal strength. RF-ACCESS RF-ACCESS KIT All descriptions and characteristics can be changed without notice or obligation.

 More



M2M TeleSystems Equipment: RF-XTEND antenna
RF-XTEND antenna
Extend your WiFarm wireless range with RF-XTEND exterior antennas!   In the event that buildings are situated too far from the WiFarm network — that is, more than 1,600 feet or 500 meters from network antennas, simply install an RF-XTEND in the appropriate location in order to extend the network range. Typical installation of an RF-XTEND exterior antenna All descriptions and characteristics can be changed without notice or obligation.

 More



M2M TeleSystems Equipment: RAN-1 radio access network
RAN-1 radio access network
The RAN-1 radio access network allows you to wirelessly connect your computer to the WiFarm network. Equipped with a USB connector, the RAN-1 is easily installed on your computer.  With the help of the FarmSite software, the RAN-1 gives you the possibility to connect to all of your controllers located within 1,600 feet (500 meters) of the nearest antenna.  And if you use a laptop to connect to your controllers, the RAN-1 gives you added mobility to manage your farm equipment from anywhere within 1,600 feet (500 meters) of the nearest WiFarm antenna. RAN-1 radio...

 More



M2M TeleSystems Equipment: MM-4U and MM-4 controller modules
MM-4U and MM-4 controller modules
MM-4 and MM-4U controller modules are designed for transferring Core 50/100 controller settings and software from one controller to another or to your computer. MM-4U controller module MM-4 controller module Once all of your personalized settings have been set in your controller, the MM-4 can transfer these to other controllers. The MM-4U is equipped on one end with a Core 50/100 compatible connector, and on the other end with a USB connector. MM-4U typical...

 More



M2M TeleSystems Equipment: CMPro-U and CM-512m controller modules
CMPro-U and CM-512m controller modules
CMPro-U and CM-512m controller modules are designed for transferring settings and software from one controller to another or to your computer. Once all of your personalized settings are set in one controller, the CM-512m can transfer your personally adjusted settings to other controllers. The CMPro-U is equipped on one end with a controller compatible connector, and on the other end with a USB connector. Once connected to a computer (with UProSoft software installed), the CMPro-U can save your personally adjusted settings to your hard drive, enable you to email us your controller settings to help...

 More



 
 
     Products and Partners

MonitrolVarifanGeniusAgriConsoleM2MFarmQuestFarmSiteWi FarmMultifanAccuFeed